Entries by Jose R.

Syrus 1 Firmware 1.3.63 – GPS Rollover Fix

Upgrade Command >SXAFU1http://dctserver.com/otap/f/1d3u63/std/;syrmag;3620afd5;< Corrections Fixed, GPS rollover issue   Please note this firmware is for Standard Syrus 1 version, it does NOT include iButton or Garmin functionality for Syrus 1. If your device’s network is behind a VPN please contact support@digitalcomtech.com for information on obtaining the firmware files. Si la red de su dispositivo está…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

Syrus 2 Firmware 2.3.50 – GPS Rollover Fix

Upgrade Command >SXAFU1http://syrus.pegasusgateway.com/otap/f/2k3v50/std/;syrmag;3620afd5;< Corrections Fixed, GPS rollover issue   An email was sent to all Support members with the following information:   A small percentage of Syrus 2 devices were affected by the recent GPS Rollover, the symptoms of this are that the date indicated by the GPS is off, and the coordinates go to…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

Syrus 3 & CloudConnect Firmwares 3.3.77

Upgrade Command >SXAFUGW< Important – Firmware 3.3.77 replaces firmwares 3.3.59 & 3.3.71, it is important that your devices are upgraded to this stable version, the changes between this release note and the previous one are detailed below in italics. After upgrading the Syrus firmware make sure to upgrade the microcontroller’s (interface) FW – see the…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

Syrus 3GBT – Bluetooth Tag Beacon Mode

The following document describes how to use the Syrus BT Tag in beacon mode, in this mode the tag can be used to detect presence and take actions immediately. Follow the guide to start monitoring your valuable assets today!

ECU Monitor Firmware 4.2.0

Upgrade Command: >SXAEM1ecu_4.2.0< Improvements Additions Corrections   Make sure your Syrus 2 is upgraded to the latest stable version before upgrading the ECU Monitor. See the footer of the support page for the latest stable versions. Important! If you’re upgrading the ECU Monitor from an ECU Firmware previous to 2.1 please read the following >>Upgrading…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

Syrus 2 Firmware 2.3.8

Upgrade Command: >SXAFU0C< Corrections Changes Improvements Additions >QXACCM< >RXACCMserver;protocol;bytes_TX;bytes_RX< >RXACCMdctserver.com,TCP,36096,0;174.36.18.171,TCP,814,345< server: dctserver.com protocol: TCP bytes_TX: 36096 (transmitted by Syrus to this server) bytes_RX: 0 (received by the Syrus from this server) server: 174.36.18.171 protocol: TCP bytes_TX: 814 (transmitted by Syrus to this server) bytes_RX: 345 (received by Syrus from this server) #Configure the 5th Day...

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

Syrus 2 Firmware 2.2.3

Corrections Changes Improvements Additions ;CI=AAA,BBB,CCC…,DDD…,EEE…,[repeats for up to the nearest 6 cell phone towers] where AAA: Mobile country code (MCC). BBB: Mobile network code (MNC). CCC…: Local Area Code (LAC). DDD…: Cell ID (CID). EEE…: RSSI level. >SMTH020100T\**\**\1B\FF;ROUTE=0;POS_FLAG=99< to configure the MDT in HEX mode and ignore the delimiters. The packet will be broken by…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

Pegasus Gateway Guide

Pegasus Gateway Guide Is avaiable now, the first Pegasus Gateway Guide – Inside, you will find relevant information and functionality of the Pegasus Gateway which has been developed to fully integrate our Syrus line of products.  Pegasus Gateway Guide – v1.4     Questions: support@digitalcomtech.com  …

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

ECU Monitor Firmware 3.3

ECU Monitor FW 4.1.3 Release Notes! Corrections Important! If you’re upgrading the ECU Monitor from a Firmware previous to 2.1 please read the following >>Upgrading Procedure! Make sure your Syrus 2 is upgraded to the firmware – 2.1.48 before proceding. Syrus 2 Upgrade Command: >SXAFU0C<   ECU Monitor Upgrade Command:        >SXAEM1ecu_33<…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here