ECU Monitor FW Release Information

ECU Monitor Firmware 5.0.16

/in /by

 UPGRADE COMMAND>SXAEM1ecu_5.0.16<UPDATESImplemented, SPN 182 – Engine Trip Fuel parameterFixed, condition where ECU would restart if XAEMP was set to 0. ie: `>SXAEMP0<`Fixed, condition where the ECU would restart if it attempted to configure ECU with the same configuration it already hadThis version is available for Syrus 3 device family only, with minimum firmware: 3.4.49. …

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

ECU Monitor Plus Firmware 6.1.5

/in , /by

UPGRADE COMMAND >SXAEM1ecu_6.1.3< Updates from 6.1.3 Added, SPN 182 Engine Trip Fuel parameter Added, DID 131 Brake Switch parameter Fixed, condition where, if Syrus attempted to configure ECU with the same configuration it already had, the ECU would restart Updates from 6.1.1 Implemented, over forty new parameters with various DIDs. Please view Parameters to add.txt […]

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

ECU Monitor Plus Firmware 6.0.4

/in , /by

Upgrade Command: >SXAEM1ecu_5.0.12< Fixed Fixed, erroneous values on the FAN Status and ABS Status parameters for J1939 protocol Please note that this upgrade can take between 8-10 minutes, so it’s recommended to do the upgrade when the vehicle’s ignition is OFF, and the ECU is powered permanently. An ignition transition would not cause loss but it […]

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

ECU Monitor Firmware 5.0.12

/in , /by

Upgrade Command: >SXAEM1ecu_5.0.12< Fixed Fixed, erroneous values on the FAN Status and ABS Status parameters for J1939 protocol Please note that this upgrade can take between 8-10 minutes, so it’s recommended to do the upgrade when the vehicle’s ignition is OFF, and the ECU is powered permanently. An ignition transition would not cause loss but it…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

ECU Monitor Firmware 5.0.11

/in , /by

Upgrade Command: >SXAEM1ecu_5.0.11< Added Added, Support for the ContiPressureCheck TPMS accessory from Continental Added, Support for the J1939 500kHz CAN networks Please note that this upgrade can take between 13-15 minutes, so it’s recommended to do the upgrade when the vehicle’s ignition is OFF, and the ECU is powered permanently. An ignition transition would not…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

ECU Monitor Firmware 5.0.3

/in , /by

Upgrade Command: >SXAEM1ecu_5.0.3< Fixed   Please note that this upgrade can take between 13-15 minutes, so it’s recommended to do the upgrade when the vehicle’s ignition is OFF, and the ECU is powered permanently. An ignition transition would not cause loss but it would delay the upgrade….

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

ECU Monitor Firmware 4.3.0

/in /by

Upgrade Command: >SXAEM1ecu_4.3.0< Fixed   Please note that this upgrade can take between 20-25 minutes, so it’s recommended to do the upgrade when the vehicle’s ignition is OFF, and the ECU is powered permanently. An ignition transition would not cause loss but it would delay the upgrade….

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

ECU Monitor Firmware 4.2.11

/in /by

Upgrade Command: >SXAEM1ecu_4.2.11< Improvements Additions Corrections   Make sure your Syrus 2 is upgraded to the latest stable version before upgrading the ECU Monitor. See the footer of the support page for the latest stable versions. Important! If you’re upgrading the ECU Monitor from an ECU Firmware previous to 2.1 please read the following >>Upgrading…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here

ECU Monitor Firmware 4.2.0

/in /by

Upgrade Command: >SXAEM1ecu_4.2.0< Improvements Additions Corrections   Make sure your Syrus 2 is upgraded to the latest stable version before upgrading the ECU Monitor. See the footer of the support page for the latest stable versions. Important! If you’re upgrading the ECU Monitor from an ECU Firmware previous to 2.1 please read the following >>Upgrading…

This content is for registered Members only. You can register for free!
Login to view this content, or Register here